Licensed and insured Mobile locksmith in North Park, San Diego · Open 8 am to 9 pm, every day

Locksmith service

Broken Key Extraction in San Diego

When a key snaps inside a lock, the piece left behind can usually be pulled out without replacing the lock. We use thin extractor tools that hook the cuts on the blade, then cut a new key from the two halves. It works for house locks, car doors and ignitions, and you get the price before we start.

Cabrillo Locksmith, licensed and insured Open 8 am to 9 pm, every day Updated

Typical price: $75 to $150 from a door lock, $90 to $200 from a car door or ignition. Full price table

Lock replaced?
Usually not. The piece comes out and the lock keeps working
Keep both halves
We cut the new key from them
Makes it harder
A piece pushed deeper, or glue in the keyway
Works on
House locks, car door locks and ignitions

When you need a broken key pulled out

You need us when part of a key is stuck inside the lock and you cannot grip it. It happens in three places:

  • House locks. Front door deadbolts, knob locks and side gates. The key often breaks while you are turning it.
  • Car door locks. Often on a car whose remote has died, so the door lock is used for the first time in months and is stiff.
  • Ignitions. The key snaps while the car is being started or switched off, sometimes leaving the ignition in the on position.

If the broken end is still sticking out and you want to try first, our page on what to do when a key breaks off in the lock walks you through it, and tells you when to stop.

How we remove a snapped key from a lock

We work with the lock as it is, and only take it apart if the piece will not come out the front. The order:

  1. Line the lock up. A key can only come out with the cylinder in the position the key went in. If it is turned part way, we turn it back first.
  2. Slide in an extractor. A thin steel blade with small hooks or a spiral edge goes in alongside the broken piece, between it and the wall of the keyway.
  3. Hook the cuts and pull. The hooks catch the cuts on the blade, and the piece is drawn straight out, a little at a time.
  4. Take the cylinder out if needed. If the piece is jammed or deep, we remove the cylinder from the door and work on it on the bench.
  5. Test it. We cut the new key, then run it in the lock several times, locked and unlocked, with you there.

What makes broken key extraction harder

A clean break with the piece sitting near the front is the quick job. Three things turn it into a longer one:

What happened Why it is harder
The piece was pushed deeper Usually by putting the other half back in to “turn it”. The tip ends up further from the extractor and wedged against the pins
Superglue was used Glue runs past the key and sets on the pins and springs. The cylinder may need to be taken apart or replaced
The lock was already stiff Dirt, corrosion or worn pins grip the piece. Salt air is a common cause near the beach in Ocean Beach and Point Loma

An ignition takes more care than a house lock, because the wafers inside are small and the cylinder is costly to replace. If the wafers are worn or damaged, the fix becomes an ignition repair.

Cutting a new key from the two broken halves

Keep both pieces of the key. With the cuts intact, we line the halves up, read the depth of each cut and cut a fresh key in the van. The new key is cut on a clean blank, so it is stronger than the one that snapped.

For a plain house key that is the end of it. For a car key with a chip in the head, the blade can be cut from the halves, but the new key still has to be programmed to the car, which is a car key replacement. Once that key works, a spare car key copied from it is a cheaper job than starting over if it breaks again. If you would rather nobody else could use an old copy of the key, we can rekey the lock while we are there.

Why keys snap

A key breaks when the lock fights it harder than the metal can take. The usual reasons:

  • Wear. Brass keys thin out over years, mostly at the shoulder where the blade meets the head.
  • A stiff lock. A dry, dirty or corroded cylinder, or a bolt rubbing on the strike, means more force on every turn. Our guide on locks that have gone stiff covers the causes.
  • Using the key as a handle. Pulling a door shut by the key bends the blade a little each time.
  • Copies of copies. Each copy loses a little accuracy, so the key lifts the pins less cleanly and needs more twist.

If one key has snapped, check the others on the same ring. A key worn thin enough to break is rarely the only one. If the lock caused the break because it is stiff, worn or rubbing on the strike, lock repair fixes it so the next key does not snap too.

What changes the price of broken key extraction

Where the key broke and how deep the piece sits decide most of the price. A house lock with the piece near the front is the cheap case. An ignition, a piece pushed deep or a keyway full of glue costs more. Ranges for each are in the table under this section, and our prices page covers the rest of our work.

What broken key extraction costs in San Diego

Broken key extraction prices in San Diego
JobTypical price
Broken key removed from a door lock: Lock left working$75 to $150
Broken key removed from a car door or ignition: Depends on how deep the piece sits$90 to $200
New house key cut from the pieces: Car keys are priced as a replacement key$5 to $20

Typical San Diego prices between 8 am and 9 pm, travel included unless a service call is listed. The exact price depends on the lock or the vehicle, and you get it before work starts.

Cabrillo Locksmith charges the same prices every day of the week. See prices for every locksmith service

FAQ

Broken key extraction questions

Will I need a new lock after a key breaks in it?

Usually not. If the lock was working before the key snapped, the piece comes out and the lock carries on as before. A new lock is only needed when the cylinder was already badly worn, when it was damaged by someone forcing it, or when glue has set inside it. We tell you which it is before we do anything.

Can you make a new key from the broken pieces?

Yes, as long as the cuts on the blade are intact. We line the two halves up, read the depth of each cut and cut a fresh key in the van. A new house key cut from the pieces typically costs $5 to $20. If a cut has broken away, we can read the lock instead.

What if the broken piece is a car key with a chip?

The chip sits in the plastic head, not the blade. We pull the blade out of the lock, cut a new blade and program a new key to the car, because a chip key has to be recognized by the immobilizer. That is priced as a replacement car key, not as a simple copy.

Why did my key snap?

Usually because the lock was already fighting it. A stiff or dry cylinder, a door that has dropped out of line with the strike, or a key worn thin at the shoulder all add strain. Using the key to pull the door shut adds more. The key gives way before the lock does.

How much does broken key extraction cost?

Removing a broken key from a door lock typically costs $75 to $150, with the lock left working. From a car door or an ignition it is $90 to $200, depending on how deep the piece sits. A new house key cut from the pieces adds $5 to $20.

My key broke in the ignition. Can I still drive the car?

No. With part of the key inside, the ignition may not turn to start or may not turn back to off and release. Leave it in park, do not try to start it with the stub, and call us. We pull the piece out at the car, so there is no tow to a shop.

Related services

Jobs that often go with broken key extraction

See all locksmith services

Call or get a quote

Tell us what happened

Call and say what happened. For a car, have the year, make and model ready. You get a range on the phone and the exact price before work starts.

(619) 940-1565

  • Open 8 am to 9 pm, every day
  • Licensed and insured
  • Serving North Park and 31 more San Diego neighborhoods and nearby cities, including La Jolla, Tierrasanta, La Mesa, National City and Coronado

Request a quote

Locked out right now? Call instead. The form is for jobs that can wait until we reply.

Call (619) 940-1565 Get a quote