Home locksmith service
Lock Change and Installation in San Diego
A new lock is worth fitting when the old one is worn, weak or missing. The strength of a deadbolt comes from three things working together: a graded lock, a bolt that throws at least an inch, and a strike plate screwed into the house framing. We fit all three, and price the job before we start.
Typical price: $100 to $250 for a standard deadbolt, lock included. Full price table
- Grade for an outside door
- ANSI/BHMA Grade 2 or Grade 1
- Bolt throw to look for
- At least 1 inch
- Strike plate screws
- At least 3 inches long, into the framing
- Older doors
- Thinner doors and mortise pockets can be adapted
When a lock should be replaced, not rekeyed
Replace a lock when the hardware itself is the problem. If the lock works smoothly and you only want new keys, a lock rekey costs less.
Signs the lock has had its day:
- The key sticks or has to be jiggled, even with a fresh copy. The pins or the plug are worn.
- The knob or deadbolt wobbles on the door, or the bolt drags as it moves.
- There is no deadbolt at all, only a spring latch in the knob that can be slipped.
- The finish is pitted or green. Salt air has worked into the lock, which is common near the ocean.
- It is a low-grade lock on an outside door, or you cannot find any grade on the packaging.
Our guide to rekeying versus replacing your locks goes deeper on the choice. If the lock is sound apart from one worn or broken part, lock repair usually costs less than a new lock.
In a rental, Civil Code section 1941.3 makes the landlord install and maintain a working deadbolt on each main swinging entry door, with exceptions such as buildings designated as historic, so ask before you change one. The state’s renter lock rules explain what a tenant may change.
What ANSI/BHMA lock grades mean
The grade tells you how hard a lock was tested. ANSI/BHMA, the American standard for builders’ hardware, rates locks Grade 1, 2 or 3 after tests of durability and strength.
| Grade | What it means | Where it belongs |
|---|---|---|
| Grade 1 | The highest of the three grades | Commercial doors, or a home entry door where you want the most |
| Grade 2 | The middle grade | Front, back and side doors of most homes |
| Grade 3 | The lowest of the three grades | Interior doors, or as a stopgap |
Look for the grade on the box or the maker’s specification sheet. If a lock does not state a grade at all, ask why before you buy it.
What makes a deadbolt strong
A deadbolt is only as strong as what the bolt locks into. The San Diego Police Department’s crime-prevention guidance calls a poorly fixed strike a weak link, and a soft wood frame easy to kick in. We look at three things:
- Bolt throw. The bolt should extend at least 1 inch into the frame. The same police guidance asks for a throw of at least 1 inch.
- Strike plate. A heavy strike plate spreads the force of a kick across more of the frame than the thin plate many locks come with.
- Long screws. Strike plate screws should be at least 3 inches long so they pass through the jamb and bite into the framing behind it. The short screws in many boxes only reach the thin jamb.
That is why we fit the strike as carefully as the lock, and why a good lock on a split or soft frame may need the frame repaired first.
Fitting new deadbolts to older doors
Many older San Diego homes need a little extra work. North Park’s Dryden Historic District alone covers 136 houses, mostly Craftsman and Spanish Revival, built between 1912 and 1941. Kensington was laid out around 1910, and both Kensington and Mission Hills are known for Spanish Revival homes from the 1920s on.
Today’s exterior doors are usually 1 3/4 inches thick, drilled with a 2 1/8-inch hole at a backset of 2 3/8 or 2 3/4 inches. Older doors may be thinner or thicker than that, and many were cut for a mortise lock: a box-shaped lock sitting in a pocket inside the door. A modern deadbolt will not drop into that pocket. The options are:
- Keep the mortise lock and service or replace it with a new mortise lock that fits the pocket.
- Cover the old cut with a plate and fit a modern lock through it.
- Add a deadbolt above the old lock, and leave the old lock as a latch.
If your home is in Kensington, Mission Hills or another older neighborhood, expect us to look at the door before we quote.
Installing a lock you supply, and coastal locks
We fit locks you have bought for $60 to $130 per lock in labor. Check that the lock matches your door’s thickness and backset before you buy. Near the water, in places like Mission Beach, the finish and materials matter as much as the grade. Our guide to the best locks for coastal homes covers what lasts in salt air. If you would rather have a keypad, see smart lock installation.
What changes the price of a lock change
Mainly the lock and the door. Swapping a deadbolt into an existing hole runs $100 to $250 with the lock. A knob or lever lock replaced in the existing holes runs $90 to $220, lock included. A high-security deadbolt with restricted keys runs $250 to $500. Drilling a door that has no deadbolt runs $150 to $300. An old mortise door takes more time, and you get the exact figure before we start. Our lock change cost guide walks through what moves a job up or down its range, and the residential locksmith page lists the rest of our home lock work.
What lock change and installation costs in San Diego
| Job | Typical price |
|---|---|
| Deadbolt replaced, lock included: Standard residential grade | $100 to $250 |
| Knob or lever lock replaced, lock included: Standard residential grade, existing holes | $90 to $220 |
| High-security deadbolt, lock included: Pick- and drill-resistant, restricted keys | $250 to $500 |
| New deadbolt on a door that has none: Door and frame drilled, lock included | $150 to $300 |
| Lock you supply, fitted: Labor only, per lock | $60 to $130 |
Typical San Diego prices between 8 am and 9 pm, travel included unless a service call is listed. The exact price depends on the lock or the vehicle, and you get it before work starts.
Cabrillo Locksmith charges the same prices every day of the week. See prices for every locksmith service
Sources
The laws and official pages behind the facts on this page. Each link opens the original document.
- Civil Code section 1941.3: dead bolt locks and window security devices in rental housing, California Legislative Information
- Landlords' and tenants' rights guide: dead bolt locks and window security, California Department of Real Estate
- Product grade levels in ANSI/BHMA standards, Builders Hardware Manufacturers Association
- ANSI/BHMA A156.2 locks and latches: summary of the tests, Builders Hardware Manufacturers Association
- Small retail business security survey: deadbolt throw, strike plates and frames, San Diego Police Department
FAQ
Lock change and installation questions
What lock grade should I use on my front door?
We suggest Grade 2 or Grade 1, the top two of the three ANSI/BHMA grades, with Grade 1 the highest. Grade 3 is the lowest grade, and we would keep it to interior doors. A Grade 2 deadbolt fitted with a proper strike plate into the framing is a sound choice for most homes.
Can you add a deadbolt to a door that does not have one?
Yes, on most wood and many fiberglass doors. We drill the door face and edge, cut the frame for the strike, and fit the lock. That runs $150 to $300 with the lock included. Hollow-core doors and some metal or glass-heavy doors are poor candidates, and we tell you if yours is one.
Will a new lock fit my old door?
Usually, with some adapting. Older doors may be thinner than the current standard, and many were cut for a mortise lock rather than a round bore. We can refurbish or replace the mortise lock, cover the old cut with a plate, or add a deadbolt above it. We look at the door before quoting.
Can I buy my own lock and have you fit it?
Yes. Fitting a lock you supply costs $60 to $130 per lock in labor. Before you buy, measure the door thickness and the backset, the distance from the door edge to the center of the hole. If the lock fails or a part is missing, we cannot vouch for hardware we did not supply.
Should I replace my locks or just rekey them?
Rekey if the locks work smoothly and you only want new keys. Replace them if they stick, wobble, are a low grade or are corroded. Replacing also makes sense when you want a different style, a keypad or a stronger deadbolt. If rekeying would do the job, we will say so.
Do I need to keep the same finish on every lock?
No. The finish is cosmetic and has nothing to do with whether locks can share a key. It matters more near the coast, where salt air pits and tarnishes cheap plated hardware. Solid brass and stainless steel parts usually hold up better than plated zinc in damp, salty air, and our coastal locks guide compares the options.
Related services
Jobs that often go with lock change and installation
Call or get a quote
Tell us what happened
Call and say what happened. For a car, have the year, make and model ready. You get a range on the phone and the exact price before work starts.
(619) 940-1565- Open 8 am to 9 pm, every day
- Licensed and insured
- Serving North Park and 31 more San Diego neighborhoods and nearby cities, including La Jolla, Tierrasanta, La Mesa, National City and Coronado