Licensed and insured Mobile locksmith in North Park, San Diego · Open 8 am to 9 pm, every day

Troubleshooting

Door Lock Stuck or Key Hard to Turn? Find the Cause

Open the door and try the lock. If the key turns freely with the door open, the lock is fine and the bolt is rubbing on the strike, so the door or the strike needs adjusting. If it is still stiff with the door open, the cylinder or bolt is dirty, dry, corroded or worn.

By the Cabrillo Locksmith team Updated

First test
Turn the lock with the door open
Turns freely open, stiff shut
The door or strike is out of line
Lubricant to use
Dry PTFE spray, or graphite used sparingly
Lubricant to avoid
Oily sprays, which hold dirt and grit

Step 1: test a stiff lock with the door open

This one test tells you whether the problem is the lock or the door. Open the door, then lock and unlock it with the key and the thumb turn several times.

  • It turns freely with the door open. The lock is fine. The bolt or latch is rubbing on the strike plate when the door is shut. Go to step 2.
  • It is stiff with the door open. The problem is inside the lock: the cylinder, the bolt or both. Go to step 3.
  • Only the key is stiff, the thumb turn is easy. The cylinder or the key is the problem, not the bolt. Go to steps 3 and 4.

Step 2: fix a lock that only sticks with the door shut

A lock that only sticks with the door shut means the bolt is not entering the strike cleanly. The usual causes:

  1. Sagging hinges. Loose screws, most often in the top hinge, let the door drop so the bolt hits the bottom of the strike. Tighten every hinge screw first.
  2. A swollen door. Wood doors take on moisture and grow in damp months, then pinch the frame. If the door rubs the frame as it closes, this is likely.
  3. A misaligned strike. Look inside the strike opening for scrape marks, bare metal or splintered wood. They show which way the bolt is hitting.

A quick check: push or lift the door while you turn the key. If the lock suddenly turns easily, the alignment is out. Moving or filing the strike plate fixes most of these, but tighten the hinges before you file anything, or you may file the wrong edge.

Step 3: clean and lubricate a stiff lock cylinder

When the lock is stiff with the door open, something inside it is dirty, dry, corroded or worn. Clean and lubricate it first.

Lubricant Use it? Why
Dry PTFE lock spray Yes, the first choice Goes on wet, dries to a slick film that does not hold dust
Graphite powder Yes, sparingly Works well in small amounts. Too much packs the cylinder, and damp air can make it clump
Oily sprays and household oil No Stay wet and collect dust and grit, so the lock gets worse
Grease No, not in the keyway Too thick for the pins and holds dirt

If someone has already put oil in the lock, flush it with a cleaner that leaves no residue and let it dry before you use a dry lubricant. Never put graphite on top of oil, because the two form a paste. One short spray into the keyway is enough. Work the key in and out and turn it a few times.

If the lock is still stiff after a clean and a dry lubricant, the parts are worn or corroded, and lubricant will not bring them back.

How salt air makes door locks stick near the coast

Near the ocean, salt air is often the cause. It carries salt and moisture into the keyway and onto the bolt, and the metal corrodes from the inside. In Ocean Beach, Point Loma, Mission Beach and Pacific Beach, we see stiff cylinders, rusted latch springs and bolts that drag in the door.

Plated and low-grade hardware fails first. A yearly clean and dry lubricant slows the damage. When a lock has corroded through, replace it with one built for salt air. Our guide to the best locks for coastal homes explains which finishes and materials last.

Stiff mortise locks on older San Diego doors

In an older San Diego house, a stiff lock may be a worn mortise lock: a steel case set in a pocket in the door edge. Many homes in Golden Hill, Kensington and Mission Hills keep their original doors. The worn part inside is usually small, a latch spring or a seized cylinder, and it is replaced with the case left on the door. An old mortise lock repaired costs $140 to $340.

Step 4: is the door key worn, or the lock?

Try another key for the same lock. If it turns smoothly, the first key is worn: its cuts have rounded off and it no longer lifts the pins to the right height. Get a new key cut from the original or to the lock’s code, not copied from the worn one.

If every key is stiff, the pins inside the lock are worn. A lock rekey replaces the pins and gives you new keys, which often fixes a worn cylinder for less than a new lock. Do not force a stiff key. That is how keys snap, and then you need broken key extraction as well.

Repair or replace a stiff door lock?

Repair the lock when cleaning, lubricating, adjusting the strike or rekeying brings it back. If you would rather not do it yourself, that is our lock repair service. Replace it when one of these is true:

  • The bolt or cylinder is corroded and still stiff after cleaning.
  • The bolt is bent, or it no longer throws all the way out.
  • The lock is a light, cheap model that has worn through.
  • You want a stronger lock or a deadbolt on a door that has none.

For a new deadbolt or a lock fitted to a door that needs it, see lock installation. We give you the price before any work starts. If you rent, ask your landlord before replacing a lock: our guide to California renter lock rules explains who may change one.

FAQ

Quick answers

Why is my key hard to turn only when the door is closed?

Because the bolt is rubbing on the strike plate in the frame. The door may have dropped on loose hinge screws, the wood may have swollen, or the strike was never quite in line. Lubricant will not fix it. Tighten the hinge screws first, then look for rub marks inside the strike opening.

Can I use WD-40 on a stiff door lock?

The classic oily spray is not a good choice. It frees the lock for a short time, but it stays wet and collects dust and grit, and the lock ends up stiffer than before. Use a dry PTFE lock lubricant instead. Some products sold under the same brand are dry PTFE sprays, so read the label.

Is graphite or PTFE better for a lock?

Both work. A dry PTFE spray goes on wet, reaches into the cylinder and dries to a slick film that does not hold dust. Graphite powder works too, but use a small puff, because too much packs the cylinder. Never put graphite into a lock that already has oil in it, or the two form a paste.

How do I know if it is the key or the lock that is worn?

Try another key for the same lock, ideally one that has had little use. If it turns smoothly, the first key is worn and needs replacing. If every key is stiff, the wear is in the lock. A key cut fresh to the lock's code gives the fairest test.

Should I repair or replace a stiff lock?

Repair it if cleaning, lubricating or adjusting the strike brings it back. Replace it when the bolt or cylinder is corroded, the lock is cheap and worn through, or you want a better lock anyway. Replacing a deadbolt with the lock included typically costs $100 to $250 for a standard residential grade.

Why do locks near the beach get stiff so quickly?

Salt air carries moisture and salt into the keyway and onto the bolt. Over time the metal corrodes, the pins and springs stick, and the bolt drags in the door. Plated and low-grade hardware goes first. A yearly clean and dry lubricant slows it, but corroded parts usually have to be replaced.

Keep reading

More guides

  • Troubleshooting

    Keys locked in the car

    What to do the moment you lock your keys in the car: when to call 911, what to check first and when a locksmith is the answer.

  • Troubleshooting

    Locked out of the house

    What to do when you are locked out of your house, in order, what not to try and what a locksmith visit costs.

  • Troubleshooting

    Locked out after 9 pm

    Locked out after 9 pm, when we are closed: when to call 911, free ways back in, and how to vet a night locksmith.

Call or get a quote

Tell us what happened

Call and say what happened. For a car, have the year, make and model ready. You get a range on the phone and the exact price before work starts.

(619) 940-1565

  • Open 8 am to 9 pm, every day
  • Licensed and insured
  • Serving North Park and 31 more San Diego neighborhoods and nearby cities, including La Jolla, Tierrasanta, La Mesa, National City and Coronado

Request a quote

Locked out right now? Call instead. The form is for jobs that can wait until we reply.

Call (619) 940-1565 Get a quote