Commercial locksmith service
Storefront Door Lock Repair in San Diego
Most storefront lock problems come from one of three parts: the cylinder the key turns, the lock body hidden inside the narrow door frame, or a sagging door that no longer lines the bolt up with the strike. We find which one it is, fix it at your door, and price it before we start.
Typical price: $80 to $180 for a cylinder, $180 to $400 for a new lock body. Full price table
- Door type
- Aluminum and glass doors with a narrow stile
- Cheapest fix
- Often a cylinder or closer, not a new lock body
- Common cause of a stuck bolt
- A door that has dropped on its pivots
- What to have ready
- Photo ID and proof you run or own the business
How a storefront door lock works
An aluminum storefront door has narrow side frames, called stiles, often only about 2 inches across. A standard house deadbolt will not fit, so these doors use a slim lock body that sits inside the stile. The key and thumb turn are separate round mortise cylinders that thread into that body from each side.
When you turn the key, the cylinder turns a cam on its back. The cam drives the mechanism inside the lock body. On most swinging shop doors that is a pivoting bolt, a curved deadbolt that swings out of the stile into the frame. Some doors use a deadlatch that springs shut, and sliding storefront doors use a hook bolt that catches a strike. A small set screw at the edge of the stile holds each cylinder in place.
That split matters for repairs. The cylinder and the lock body are two different parts, priced differently, and the cheaper one is often the culprit.
Common storefront lock failures
Each symptom points to a part. Here is what we check first:
| Symptom | Usual cause | Typical fix |
|---|---|---|
| The whole cylinder spins in the door | Set screw backed out, cylinder turning in its threads | Reset and tighten the cylinder, or replace it if the threads are damaged |
| Key goes in but will not turn | Worn pins, a worn key or grit in the cylinder | Clean, rekey or replace the cylinder |
| Key turns, bolt does not move | Worn or loose cam, or a broken lock body | New cam or cylinder; lock body if the inside has failed |
| Bolt will not throw or retract fully | Door out of line, bolt rubbing the strike | Realign the door or adjust the strike |
| Thumb turn feels loose or floppy | Thumb turn cylinder loose, or its cam worn | Tighten or replace the thumb turn cylinder |
If the key is hard to turn but still works, why a lock gets hard to turn explains what is happening inside the cylinder. If the key snapped off, leave the piece where it is and see broken key extraction.
Storefront cylinder or lock body: which needs replacing?
Start with the cylinder. It is the part you touch every day, it wears the fastest, and it comes out with a set screw and a few turns. Rekeying or replacing it costs less than a new lock body.
The lock body needs replacing when the bolt is bent, the internal parts are broken, or it no longer throws even with a new cylinder fitted. It is the same narrow body inside the stile, so before ordering we measure how far the cylinder sits in from the stile edge and match it. Replacing a body does not mean replacing the door.
When the storefront door, closer or pivots are the problem
A storefront door is heavy glass hanging on pivots or hinges, and it is pulled shut by a closer. When any of those wear, the door drops or stops short, and the bolt misses the hole in the strike. The lock gets the blame, but the door is the cause.
Signs the problem is the door rather than the lock:
- The door drags on the threshold or rubs the frame at the top corner.
- The key only turns if you lean on the door.
- The door does not fully close on its own, or it slams.
- There are fresh scrape marks around the strike.
We adjust closers and strikes and can replace a worn closer, priced before we start. Pivot replacement or a bent door frame can need a storefront door company, and we will say so.
Storefront doors on San Diego shopping streets
We come to shops, cafes and restaurants on the business streets in our area, including 30th Street and University Avenue in North Park, Adams Avenue through Normal Heights and Kensington, Newport Avenue in Ocean Beach and Garnet Avenue in Pacific Beach. Near the coast, salt air corrodes cylinders and pivots faster, so a stiff lock there is often worth cleaning before it fails. We also work on shop doors in Downtown San Diego.
What to have ready for a storefront lock repair
- Photo ID and proof of the business, such as a lease or a business license. We write a work order before opening or changing a business lock.
- A photo of the lock on both sides of the door, if you can send one. It helps us bring the right cylinder.
- Your other keys, if you want the storefront to match the back door. That is a rekey or a master key system.
For other business doors, see our commercial locksmith page.
What storefront door lock repair costs in San Diego
| Job | Typical price |
|---|---|
| Storefront lock cylinder rekeyed or replaced: Mortise cylinder on an aluminum and glass door | $80 to $180 |
| Storefront lock body replaced: Swing bolt or latch inside the door stile | $180 to $400 |
| Door closer adjusted or replaced: Adjustment at the low end, new closer at the high end | $95 to $450 |
Typical San Diego prices between 8 am and 9 pm, travel included unless a service call is listed. The exact price depends on the lock or the vehicle, and you get it before work starts.
Cabrillo Locksmith charges the same prices every day of the week. See prices for every locksmith service
FAQ
Storefront door lock repair questions
Why does my storefront key turn but the door stays locked?
The cam on the back of the cylinder is not moving the bolt. Either the cylinder has loosened and turned in its threads, the cam has worn or slipped, or the lock body inside the door has broken. We pull the cylinder and look at the cam first, because that is the cheaper repair.
Can you rekey a storefront lock instead of replacing it?
Usually, yes. The keyed part is a separate round cylinder that threads into the lock body. We can rekey it to a new key, or match it to the other locks in the building, without touching the lock inside the door. The lock body is only replaced when it is worn or broken.
Why do I have to push or pull the door before the key turns?
The door has moved out of line with the frame, so the bolt is pressing on the edge of the strike. Worn pivots, loose hinges or a closer that no longer pulls the door fully shut are the usual causes. Fixing the door alignment often fixes the lock without replacing anything.
Should I spray lubricant into a stiff storefront lock?
Use a lubricant sold for lock cylinders, and only a small amount. Oil-based sprays collect grit and dust from the street and can make a cylinder stickier within a few months. If the key is still hard to turn after that, the pins or the cam are worn.
Do you repair the glass or the aluminum door frame?
No. We repair and replace the locks, cylinders, thumb turns, strikes and closers. Broken glass, cracked door rails and bent aluminum frames are work for a glass and storefront company. If the frame damage is what stops the lock from working, we will tell you so before charging for a lock repair.
Related services
Jobs that often go with storefront door lock repair
Call or get a quote
Tell us what happened
Call and say what happened. For a car, have the year, make and model ready. You get a range on the phone and the exact price before work starts.
(619) 940-1565- Open 8 am to 9 pm, every day
- Licensed and insured
- Serving North Park and 31 more San Diego neighborhoods and nearby cities, including La Jolla, Tierrasanta, La Mesa, National City and Coronado