Licensed and insured Mobile locksmith in North Park, San Diego · Open 8 am to 9 pm, every day

Guide

Putting a Smart Lock on an Old Door in San Diego's Older Neighborhoods

Most old doors can take a smart lock. The least invasive option is a retrofit unit that fits over the inside of your existing deadbolt and leaves the outside untouched. Doors with mortise locks, unusual thickness or a dragging bolt need more thought, so measure the door before you buy anything.

By the Cabrillo Locksmith team Updated

Least invasive
A retrofit unit over your existing deadbolt
Standard bore hole
2-1/8 inches across
Standard backsets
2-3/8 inches or 2-3/4 inches
Fitting a lock you supply
$100 to $200, plus $50 to $150 if the door needs prep

Can an old door take a smart lock?

Yes, most can. The question is how much the door needs changing first, and that depends on what is already in it.

Much of North Park, Mission Hills and Kensington was built between the 1910s and the 1930s, and South Park has many older houses too. Those doors were made before today’s lock sizes settled. Some still have their original mortise locks, others have been bored for a deadbolt since, and plenty have settled in their frames over a century.

What makes an old door awkward for a smart lock

Four things cause most of the trouble.

  • Thickness. Most modern residential locks are made for doors 1-3/8 to 1-3/4 inches thick. Older and custom doors can be thinner or thicker than that. A smart lock may need a thick-door kit, and not every model has one.
  • Backset and bore size. Today’s standard is a 2-1/8 inch hole through the face of the door, with its center 2-3/8 inches or 2-3/4 inches from the door edge, which is called the backset. A 1 inch hole in the edge takes the bolt. An older deadbolt may sit in a smaller hole or at an odd backset.
  • Mortise locks. Before cylindrical locks took over around the middle of the last century, most houses used mortise locks: a steel box set into a pocket cut in the door edge. A standard smart deadbolt does not fit that pocket.
  • Settled doors. An old door that has dropped or a frame that has shifted makes the bolt rub on the strike plate. You can push a key past that drag. A smart lock’s motor cannot, so it stalls and reports a jam.

Smart lock options for old doors, least to most invasive

Option What it involves Best for
Retrofit unit over the existing deadbolt Replaces only the inside thumbturn. Outside of the door and your keys stay the same A door that already has a working deadbolt
New smart deadbolt in the existing holes Old deadbolt out, smart deadbolt in, if the bore and backset match A standard deadbolt hole in good shape
Mortise-compatible smart lock A smart lock made to work with a mortise lock body Doors where the mortise lock is the only lock
New boring A new 2-1/8 inch hole and edge bore for a deadbolt, usually above the old lock Doors with no deadbolt, or a hole too damaged to reuse

Start at the top and stop at the first option that fits. A retrofit unit is the easiest to remove later, which matters on a door you want to keep original. New boring is permanent. See smart lock installation for how we fit each one, or lock installation if you would rather have a plain deadbolt where none exists.

How to measure an old door for a smart lock

Five measurements tell you which locks will fit. Take them before you order.

  1. Door thickness. Measure the edge of the door with a tape. Compare it with the range on the lock’s box.
  2. Backset. Put the tape on the edge and read where the middle of the deadbolt hole falls. Expect either 2-3/8 inches or 2-3/4 inches.
  3. Bore size. Measure across the hole on the face of the door with the lock removed, or ask us to on the visit.
  4. Lock type. Look at the door edge. A tall rectangular faceplate with a knob and a keyhole below it usually means a mortise lock.
  5. Bolt travel. Lock and unlock with the door closed. If the bolt rubs or needs a push, the strike needs adjusting before any smart lock goes in.

If the numbers do not match a standard size, tell us on the phone. We will say which options fit before you buy anything. A dragging bolt or a tired original mortise lock is a lock repair job, done before the smart lock goes in.

Keeping original door hardware with a smart lock

You do not have to throw away a century-old lock to get a smart one. A retrofit unit or a new deadbolt above the old lock lets the original knob, plate and mortise box stay where they are. If anything does come off, bag it with its screws and label it, so it can be refitted before you sell.

If your house is a designated historic resource or sits in a historic district, check with the City of San Diego’s historic resources staff before changing hardware on an original door: the city reviews alterations there even when no permit is needed.

Smart lock costs and mistakes on older doors

The three mistakes we see most on older doors:

  • Buying before measuring. A lock that does not fit the thickness or backset goes back in its box.
  • Ignoring a dragging bolt. The motor stalls and the lock reports jams until the strike is fixed.
  • Boring a new hole when a retrofit would have done. New boring cannot be undone on an original door.

On price, the lock and the prep are separate lines. A lock we supply and fit runs $250 to $600 by model, a lock you bought yourself is $100 to $200 to fit, and any drilling or realignment adds $50 to $150. Our lock change cost guide sets those figures beside plain deadbolts. For locks that cope with salt air, see locks for coastal homes. If a key already fights you, start with what makes a door lock stick.

Sources

The laws and official pages behind the facts on this page. Each link opens the original document.

FAQ

Quick answers

Can you put a smart lock on an old door?

Usually, yes. If the door already has a working deadbolt, a retrofit unit can mount over its inside thumbturn with no new holes. Doors with only an old mortise lock, a dragging bolt or an unusual thickness need a different lock or some prep work first, so measure before you buy.

What is a retrofit smart lock?

It is a motorized unit that replaces only the inside thumbturn of your existing deadbolt. The outside of the door, the keyhole and your current keys stay the same. It is the least invasive option and the easiest to undo, which suits renters and anyone keeping original hardware.

Will a smart lock fit a thick old door?

Many smart deadbolts are made for doors between 1-3/8 and 1-3/4 inches thick. Older and custom doors can be thinner or thicker than that. Some makers sell thick-door kits with longer screws and parts, but not every model has one. Measure your door and check the lock's listed range before buying.

My old door has a mortise lock. Can it take a smart lock?

Yes, but not a standard smart deadbolt dropped into the same pocket. The options are a smart lock made to fit a mortise lock body, a retrofit unit on a separate deadbolt, or a new deadbolt bored above the mortise lock. The right one depends on the lock body and the door's condition.

Why does my smart lock keep saying it is jammed?

On older doors, the usual cause is settling: the door has dropped, so the bolt rubs the edge of the strike hole. A hand can force a bolt past that drag, but the lock's motor cannot. Run the lock with the door standing open. If it locks cleanly that way but jams once the door is shut, the door or the strike needs adjusting.

How much does it cost to install a smart lock on an older door?

On an old door the prep decides the bill more than the lock. If your deadbolt hole is sound, fitting a lock you bought is $100 to $200. A settled door or a door with no hole adds $50 to $150 for drilling or realignment. Measure first, and tell us the numbers on the phone.

Keep reading

More guides

  • Guide

    Vacation rental locks

    How to choose and run the locks on a San Diego short-term rental: a code for every guest, a key backup, salt air and rekeys.

  • Guide

    Car key replacement cost

    Typical San Diego prices for each type of car key, what losing every key adds and how to compare a locksmith's quote with the dealer's.

  • Guide

    Rekey cost

    What a rekey bill is made of in San Diego, why each extra lock costs less, what a typical home pays and how to keep the total down.

Call or get a quote

Tell us what happened

Call and say what happened. For a car, have the year, make and model ready. You get a range on the phone and the exact price before work starts.

(619) 940-1565

  • Open 8 am to 9 pm, every day
  • Licensed and insured
  • Serving North Park and 31 more San Diego neighborhoods and nearby cities, including La Jolla, Tierrasanta, La Mesa, National City and Coronado

Request a quote

Locked out right now? Call instead. The form is for jobs that can wait until we reply.

Call (619) 940-1565 Get a quote