- What the VIN can give
- The key code, where the automaker releases it
- Who can look it up
- Dealers, and locksmiths in the NASTF security registry
- What to bring
- Driver's license and the registration or title
- Chip keys and fobs
- Still programmed at the car, with the car present
What a VIN does for a new car key
For many cars, a locksmith can make a key from the VIN, but not directly. The VIN leads to the key code, and the key code is what gets cut.
The vehicle identification number names one car. For many models, the automaker keeps a record of the key code that goes with it: a short code for the depth of every cut on the blade. Fed that code, a key machine cuts a blade that fits the locks as they left the factory.
| What the VIN can lead to | What it cannot do | |
|---|---|---|
| The blade | The key code, where the automaker releases it | Fit a lock that was replaced after the car was built |
| The chip or fob | Security codes some cars ask for during programming | Start the car without programming done at the car |
| Who can use it | A dealer or a registered locksmith | Anyone who simply reads it off the dash |
How a registered locksmith gets the key code
In the United States, automakers release key codes to independent locksmiths through the National Automotive Service Task Force, or NASTF. Its Vehicle Security Professional registry and Secure Data Release Model let vetted professionals request security data, from mechanical key codes to immobilizer and PIN codes, from participating automakers.
NASTF’s published terms set the conditions:
- Every user is checked. Each person who uses the registry passes a background check and gets their own VSP ID. An account is valid for two years.
- A license is required for key codes. NASTF requires a locksmith license from anyone who uses the registry to get key codes.
- The code is for one job. It may not be stored, shared or used to make a key and mail it.
- The car and owner must be there. The professional confirms ownership in person before using the code.
Not every locksmith is registered, and registration does not reach every automaker. When you call a locksmith, ask how they will get the cuts for your car.
ID and paperwork for a key made from the VIN
Bring your driver’s license and the registration or title. Two sets of rules ask for them.
NASTF’s terms tell a registered professional to check a US or Canadian driver’s license, confirm the ownership papers match your name and address, and confirm the VIN on the car matches the VIN on those papers.
California adds its own record. Business and Professions Code section 6980.55, subdivision (b), says a locksmith who makes a key for a vehicle must put on a work order your name, date of birth and driver’s license or ID number, the vehicle’s registration or identification number, the date and your signature. The locksmith keeps a copy for two years, open to inspection by a peace officer or the Bureau of Security and Investigative Services.
If the registration is in the locked car, say so on the phone: we can open the car first. Whoever you hire, look up their state locksmith license before they arrive.
When the VIN route to a key code is closed
A VIN lookup is not always possible. These are the cases we can point to:
- The automaker sets the terms. The registry only reaches participating automakers, and each one can demand its own registration, subscription and fees.
- A lock was replaced. The code describes the factory locks. A door lock or ignition fitted later will not match a key cut to it.
- Only the dealer can key the car. That applies to some of the newest models and some European cars.
Other ways a locksmith reads the cuts for a car key
When the VIN gives nothing, the cuts can come from the car itself. We decode a door lock or the ignition cylinder, then cut a key to that code in the van, as our car key replacement page describes. If the old key snapped, the two halves are enough to read the cuts.
The way to skip all of this is a spare. While one key still works, a second one is a copy job: see spare car keys.
Where the VIN is on a car and its paperwork
Federal rules make every VIN 17 characters long and require it to be readable through the windshield by someone standing outside, next to the left windshield pillar. On a US car that is the driver’s side. Look in these places:
- On the dash, seen from outside through the bottom corner of the windshield, driver’s side.
- On the certification label on the driver’s door edge or door jamb.
- On the title and the registration card.
A photo of the plate saves reading the characters out over the phone.
What a car key made from the VIN costs
The VIN lookup is part of making the key, so the price follows the type of key. A plain metal key is $60 to $150 and a chip key cut and programmed is $120 to $275. A remote-head or flip key is $150 to $350, smart keys for push-button start are $220 to $550, and European makes run $300 to $900. With no working key to copy, add $50 to $200.
What puts a car at the top or bottom of each range is covered in our guide to car key replacement cost in San Diego. If every key is gone, read the lost car keys with no spare checklist first: it says what to gather.
Sources
The laws and official pages behind the facts on this page. Each link opens the original document.
- Business and Professions Code section 6980.55: locksmith work orders, California Legislative Information
- 49 CFR 565.13: VIN content and location requirements, U.S. Government Publishing Office (govinfo)
- 49 CFR 567.4: the certification label on the driver's door, which shows the VIN, U.S. Government Publishing Office (govinfo)
- Vehicle Industry Registration Procedures Manual 1.115: registration by VIN, on the title and registration card, California Department of Motor Vehicles
- VSP Registry and Secure Data Release Model: Terms and Conditions of Use, National Automotive Service Task Force (NASTF)