- Most common cause
- A flat fob battery, usually a CR2032 or similar coin cell
- Quick test
- If the spare fob works, the problem is the first fob
- Still get in
- Use the metal key blade hidden inside most fobs
- Fob battery
- Change it yourself. Fitted during another job: $10 to $25
Check the key fob battery first
A flat battery in the fob is the most common reason it stops working, and it is the cheapest fix. The warning signs come before it dies completely:
- The range shrinks until you have to stand next to the car.
- You press a button two or three times before the car reacts.
- A push-button car shows a message that the key is not detected.
Most fobs take a flat lithium coin cell. The CR2032 is the most common, and others use a CR2025, CR2016 or CR2450. The number is printed on the old cell and in your owner’s manual. Buy that exact number: a CR2025 is the same width as a CR2032 but thinner, so it can sit loose and lose contact. Changing it yourself is the cheapest fix. If we are already at the car for another job, such as programming a fob, we fit a new cell for $10 to $25.
Try the spare fob, then the car’s battery
The spare tells you where the fault is. If the spare fob works, the problem is the first fob. If the spare fails too, look at the car.
The car’s receiver needs power to hear the fob. A weak car battery shows itself as dim dash lights, a slow or clicking start, or nothing at all. In that case, charge or jump-start the car battery before blaming either fob.
Getting in and starting the car with a dead fob
A dead fob does not have to strand you. Most fobs carry a backup for each job.
Getting in with the hidden key blade
Most fobs hide a metal key blade. It comes out when you press a small release button or slide a catch on the side or back of the fob. The keyhole is usually on the driver’s door handle, and on many cars it sits behind a small plastic cap at the end of the handle that you lever off with the tip of the key. A few newer cars have no keyhole at all. Find yours in the owner’s manual now, before you need it.
Starting a push-button car
Most push-button cars can read a fob with a flat battery if you hold it right against the right spot. On many cars that spot is the start button: press the brake, touch the fob to the button and press it. Others have a marked area on the steering column or console, or a slot for the fob. The spot and the steps vary by make and model, so check your owner’s manual for yours.
What to do if your key fob got wet
Open it straight away and take the battery out. Do not press the buttons, which can push water further into the circuit board. Let the parts dry completely for a few days, then fit a fresh battery rather than the old one.
Fresh water is often survivable. Salt water is harder on the board, and a fob that went into the ocean usually needs replacing. If you swim or surf, read where to leave your car key at the beach so the next fob stays dry. Do not buy a cheap replacement fob online before checking it suits your car: many cannot be programmed.
When a key fob has lost its pairing with the car
If the fob has a fresh battery, its light flashes when you press a button and the car still ignores it, the fob has probably lost its pairing with the car. On some cars this happens after a battery change or after the car’s battery has been disconnected.
The fix is to program the fob to the car again. Your owner’s manual says whether your car has a method you can do yourself. Otherwise it takes a programmer plugged into the port under the dash. Programming a fob you supply costs $60 to $150, if the part is compatible. See key fob programming for how the job is done.
Getting a key fob programmed in San Diego
We program and replace key fobs at the car, wherever it is parked: a driveway in Clairemont, a curbside spot or an apartment garage. We do fob work from 8 am until 9 pm, any day of the week, but not overnight. Before you call, have these ready:
- Every fob you still have. On most cars, clearing a lost fob wipes every fob the car knows, and only the ones in hand go back on.
- Photo ID and the registration. A fob starts or opens the car, so we check that the car belongs to you before programming.
- The year, make and model. With those, the call gives a price range. The firm figure comes at the car, before we plug anything in.
When a key fob needs replacing
Replace the fob when it is cracked, water-damaged beyond drying, or lost. A new remote supplied and programmed costs $120 to $350, and a smart key for push-button start $220 to $550. If you have no second fob, that is a good moment to get a spare car key made too. If the fob is lost along with every other key, it becomes a car key replacement job, and the San Diego car key price guide breaks down what you would pay. If the fob died and the keys are now shut inside the car, see keys locked in the car.